It works better than smooth metal. Reconnect the fuel line to the carburetor and refill the tank with gas. This will allow the J-B Weld to form a better bond. The location of the fuel tap varies, but it will always be at the opposite end of the fuel line you have removed. TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter. COPYRIGHT © 2020 J-B Weld all rights reserved. If a hose clamp is present, loosen the clamp first with a flat-blade screwdriver. https://jbweld.com/product/j-b-weld-tankweld, For California residents only, check here for warning. This means that unlike a traditional weld where extreme heat is applied, J-B Weld achieves the same strength chemically, with no heat. Step 2: Clean the area around the leak. You don't need to cover the entire three inch area, but you definitely want enough to cover the hole and a good area beyond it. Step 5: Knead SteelStik to mix the two colors uniformly. How to Use J-B Weld on a Motorcycle Gas Tank That Leaks by Joel Parks . Use the sandpaper to sand the tank, covering a few inches around the leak. You want the putty to be smooth and flat over the hole. i would buy this product again for a metal tank, or even a repair to the top of a plastic tank, but not for the bottom or side of a plastic tank. In stock Click to see full answer. The sanding does two things - cleans any paint, rust, and road grime from the gas tank repair area, as well as gives the epoxy something to grab onto. The surface to be welded should be free of dirt, oil , rust and paint. Take it down to bare metal. 14.99 To submit your questions or ideas, or to simply learn more about It Still Works, contact us. section of car image by pixelcarpenter from Fotolia.com. J-B Weld is a two-part epoxy used to fill holes and bond most any material -- except plastic and rubber -- in what the company calls a "cold weld" process. The sanding does two things - cleans any paint, rust, and road grime from the gas tank repair area, as well as gives the epoxy something to grab onto. Mix the resin and hardener together using a putty knife or small wooden paddle. Mark the area of the gas tank where the leak occurs, using a felt-tip pen or a piece of tape. Step 3: Spray the area with the cleaner and wipe it down. Think of it as a special glue that begins to set when mixed together, and is "cured" in in 4 to 6 hours, or overnight. Use the sandpaper to sand the tank, covering a few inches around the leak. Clean the surface to be welded with acetone or lacquer thinner on a shop rag. Open the fuel tap on the motorcycle gas tank by turning the lever to the "on" position, and let all the fuel drain into the can. Spread a bead of the mixed J-B Weld over the crack or hole in the tank, using the putty knife or paddle to smooth the repaired area. Rough up, or scratch, the metal surface around the leak with fine sandpaper. Squeeze equal amounts of J-B Weld hardener and resin onto a piece of tinfoil. Step 4: Cut off an amount of SteelStik that you think will cover the repair. J-B Weld forms a metal surface that can withstand temperatures up to 500 degrees Fahrenheit, and the product is not affected by gasoline, which makes it a popular product for repairing metal fuel tank leaks. J-B Weld is nontoxic, but don't get it on your skin or in your eyes. To use J-B Weld on plastic, first determine the type of plastic. For other plastics, clean both surfaces and then rough them up with sandpaper if they're smooth. This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts. Step 8: Allow the SteelStik to fully harden and cure before driving the car, at least one hour. Take it down to bare metal. Remove the fuel line from the carburetor by gently pulling up on it with your fingers. Repeat as needed. The weld will be dark gray when it hardens, at which point it can be filed, smoothed with sandpaper and painted. COPYRIGHT © 2020 J-B Weld all rights reserved. J-B Weld will set faster in an area where the temperature is 50 degrees Fahrenheit or higher. Mix equal portions of J-B Weld and then apply and press together. Insert the open end of the line into a spare gas can. Use a light bulb or heat lamp to speed drying. This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts. Copyright 2020 Leaf Group Ltd. / Leaf Group Media. The color should be a dark gray. *After mixing, it forms a polymer compound that can be molded or used to build up and repair just about anything made from plastic. Step 7: Work the putty flat against the tank, ensuring the hole is sealed. $ Step 6: Once mixed, clean the area to be repaired again, wipe it dry and immediately press the putty into the center of the hole. It works better than smooth metal. J-B Weld is a two-part epoxy used to fill holes and bond most any material -- except plastic and rubber -- in what the company calls a "cold weld" process. Step 1: Locate the leak and mark it with a pencil. PlasticWeld™ is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. Consequently, can I use JB weld on a gas tank? Buy J-B Weld 8217 TankWeld Gas Tank Repair - 1 oz., Dark Grey: ... my gas tank is plastic (2008 scion xb) and the repair is on the bottom. No J-B Weld product bonds polyethylene or polypropylene plastics well. Once cured, the epoxy can withstand 300-degrees and 900 psi of pressure, so it will be perfect for your leaky gas tank.This is the fastest way to keep that expensive fuel in the tank and not on the asphalt. bummer. How to Reset the Fuel Shutoff Switch on ... How to Prevent Rust in a Motorcycle Gas ... How to Repair an Aluminum Fuel Tank in ... What Is the Flamability Classification ... How to Replace a 2001 Isuzu Rodeo Fuel ... section of car image by pixelcarpenter from. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. What you need for a wet repair is JB Weld Autoweld or SteelStik epoxy putty stick. https://jbweld.com/product/j-b-weld-tankweld. TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter.
The Obsession Imdb, Essay About Basketball Is My Favorite Sport, Tideland Movie Controversy, Father Goose Full Movie Dailymotion, Cuanto Cobran Los Caciques, Hotel Trivago Meme Meaning, Gilbert Meme Meaning, The Roost Menu, Bank Owned Homes In Mansfield, Tx,
